Electrical tester
Fluke FEV100 Electric Vehicle Charging Station EVSE Test Adapter
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope. Use the FEV100 to verify an EVSE is working properly after install and during periodic maintenance, or troubleshoot an EVSE if it is not delivering the appropriate charge.
Electrical safety
EVSE charging cables may become damaged over the course of use, increasing electric shock risks to users. Stay protected from and check risk of electric shock with the GFCI trip test. This function verifies the breaker of the EVSE is connected by detecting ground faults. Additionally, the PE grounding protection pre-test verifies that there is no presence of dangerous voltage at the ground terminal.
Simplicity and convenience
Perform a variety of tests including ground fault checks, insulation of wires, measuring voltage and duty cycle to see max current available for charging all in one adapter that safely integrates with the Fluke portfolio of test and measurement tools. There is no need to bring an electric vehicle onsite for EVSE troubleshooting: the adapter acts as an electric vehicle when connected to an EVSE for easy performance and maintenance testing.
Recommended tools for use with the FEV100
Key features
• Check protective earth for correct wiring and functioning with the PE pre-test feature.
• Perform GFCI troubleshooting of EVSE and verify operation within safety standards.
• Test charging states of EVSE with CP state simulation.
• Verify charging voltage and maximum available current using a multimeter.
• SAE J1772 compliant to North American standards.
Electrical safety
EVSE charging cables may become damaged over the course of use, increasing electric shock risks to users. Stay protected from and check risk of electric shock with the GFCI trip test. This function verifies the breaker of the EVSE is connected by detecting ground faults. Additionally, the PE grounding protection pre-test verifies that there is no presence of dangerous voltage at the ground terminal.
Simplicity and convenience
Perform a variety of tests including ground fault checks, insulation of wires, measuring voltage and duty cycle to see max current available for charging all in one adapter that safely integrates with the Fluke portfolio of test and measurement tools. There is no need to bring an electric vehicle onsite for EVSE troubleshooting: the adapter acts as an electric vehicle when connected to an EVSE for easy performance and maintenance testing.
Recommended tools for use with the FEV100
Key features
• Check protective earth for correct wiring and functioning with the PE pre-test feature.
• Perform GFCI troubleshooting of EVSE and verify operation within safety standards.
• Test charging states of EVSE with CP state simulation.
• Verify charging voltage and maximum available current using a multimeter.
• SAE J1772 compliant to North American standards.
Download
Product Lainnya
LVD2 volt light, offered by Fluke combines a non-contact AC voltage detector and LED flashlight into one easy to use pen-style design. It features dual sensitivity detection, turning blue from 1” to 5” (2.54 cm to 12.7 cm) from the source and red when at the source. The LVD2 is a CAT IV 600 V rated and is suitable for commercial and industrial applications.
Key Features
• Non-contact AC voltage tester and LED flashlight
• Detects from 90 to 600 V AC
• Features dual-sensitivity for two levels of detection
• Indicates proximity to AC voltage source with blue light
• Indicates you’re at the source with red light
• Ultra-bright white LED light with 100,000-hour bulb life
• Safety rated to CAT IV 600 V
• Operating temperature 0°C to 50°C
• AAA battery included
Key Features
• Non-contact AC voltage tester and LED flashlight
• Detects from 90 to 600 V AC
• Features dual-sensitivity for two levels of detection
• Indicates proximity to AC voltage source with blue light
• Indicates you’re at the source with red light
• Ultra-bright white LED light with 100,000-hour bulb life
• Safety rated to CAT IV 600 V
• Operating temperature 0°C to 50°C
• AAA battery included
• Non-contact voltage detection from 90 to 1000 V AC
• Innovative 'Battery Check' ensures battery is in good condition*
• Integrated clip design, optimized for pocket storage
• Innovative 'Battery Check' ensures battery is in good condition*
• Integrated clip design, optimized for pocket storage
Fluke 1662 menawarkan keandalan Fluke, pengoperasian yang mudah, dan semua kemampuan pengujian yang diperlukan untuk pengujian instalasi sehari-hari.
Fitur utama
Fluke 1662 memberi lebih banyak daya di tangan Anda dengan menguji semua pengaturan lokal secara cepat dan efisien.
Fungsi pengukuran
• Fungsi pengukuran
• Tegangan & frekuensi
• Pemeriksa polaritas perkabelan, mendeteksi kerusakan kabel N
• Resistansi insulasi
• Kontinuitas & resistansi
• Pengukuran kumparan motor dengan pengujian kontinuitas
• Resistansi loop & line
• Prospective earth fault current (PEFC/IK)
• Prospective short-circuit current (PSC/IK)
• Waktu switching RCD
• Tingkat tripping RCD (pengujian ramp)
• Mengukur waktu trip & arus untuk RCD tipe A & AC dalam satu pengujian
• Arus variabel RCD
• Urutan pengujian RCD otomatis
• Indikator urutan fase
Fitur lainnya
• Auto Start otomatis yang dapat diaktifkan/dinonaktifkan untuk pengujian RCD & Loop
• Pengujian mandiri
• Tampilan yang terang
• Waktu dan tanggal (jika digunakan dengan perangkat lunak opsional FlukeView)
Aksesori yang disertakan
• Satu kabel jalur input tugas berat
• Hard case
• Probe remote control
• Zero adapter
Fitur utama
Fluke 1662 memberi lebih banyak daya di tangan Anda dengan menguji semua pengaturan lokal secara cepat dan efisien.
Fungsi pengukuran
• Fungsi pengukuran
• Tegangan & frekuensi
• Pemeriksa polaritas perkabelan, mendeteksi kerusakan kabel N
• Resistansi insulasi
• Kontinuitas & resistansi
• Pengukuran kumparan motor dengan pengujian kontinuitas
• Resistansi loop & line
• Prospective earth fault current (PEFC/IK)
• Prospective short-circuit current (PSC/IK)
• Waktu switching RCD
• Tingkat tripping RCD (pengujian ramp)
• Mengukur waktu trip & arus untuk RCD tipe A & AC dalam satu pengujian
• Arus variabel RCD
• Urutan pengujian RCD otomatis
• Indikator urutan fase
Fitur lainnya
• Auto Start otomatis yang dapat diaktifkan/dinonaktifkan untuk pengujian RCD & Loop
• Pengujian mandiri
• Tampilan yang terang
• Waktu dan tanggal (jika digunakan dengan perangkat lunak opsional FlukeView)
Aksesori yang disertakan
• Satu kabel jalur input tugas berat
• Hard case
• Probe remote control
• Zero adapter
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope. Use the FEV100 to verify an EVSE is working properly after install and during periodic maintenance, or troubleshoot an EVSE if it is not delivering the appropriate charge.
Electrical safety
EVSE charging cables may become damaged over the course of use, increasing electric shock risks to users. Stay protected from and check risk of electric shock with the GFCI trip test. This function verifies the breaker of the EVSE is connected by detecting ground faults. Additionally, the PE grounding protection pre-test verifies that there is no presence of dangerous voltage at the ground terminal.
Simplicity and convenience
Perform a variety of tests including ground fault checks, insulation of wires, measuring voltage and duty cycle to see max current available for charging all in one adapter that safely integrates with the Fluke portfolio of test and measurement tools. There is no need to bring an electric vehicle onsite for EVSE troubleshooting: the adapter acts as an electric vehicle when connected to an EVSE for easy performance and maintenance testing.
Recommended tools for use with the FEV100
Key features
• Check protective earth for correct wiring and functioning with the PE pre-test feature.
• Perform GFCI troubleshooting of EVSE and verify operation within safety standards.
• Test charging states of EVSE with CP state simulation.
• Verify charging voltage and maximum available current using a multimeter.
• SAE J1772 compliant to North American standards.
Electrical safety
EVSE charging cables may become damaged over the course of use, increasing electric shock risks to users. Stay protected from and check risk of electric shock with the GFCI trip test. This function verifies the breaker of the EVSE is connected by detecting ground faults. Additionally, the PE grounding protection pre-test verifies that there is no presence of dangerous voltage at the ground terminal.
Simplicity and convenience
Perform a variety of tests including ground fault checks, insulation of wires, measuring voltage and duty cycle to see max current available for charging all in one adapter that safely integrates with the Fluke portfolio of test and measurement tools. There is no need to bring an electric vehicle onsite for EVSE troubleshooting: the adapter acts as an electric vehicle when connected to an EVSE for easy performance and maintenance testing.
Recommended tools for use with the FEV100
Key features
• Check protective earth for correct wiring and functioning with the PE pre-test feature.
• Perform GFCI troubleshooting of EVSE and verify operation within safety standards.
• Test charging states of EVSE with CP state simulation.
• Verify charging voltage and maximum available current using a multimeter.
• SAE J1772 compliant to North American standards.